Updating netbackup server list via script

6854933580_2c8b688306_z

You will be redirected to another page and you need to select the appropriate Plugin binaries.

Once downloaded copy to the server and follow the following steps.

ULTRIUM5-SCSI.050 Yes Yes MED005 Yes hcart3 vmdbitest /dev/nst0 AVR In addition, the options -activate_host and -deactivate_host can be used to activate or deactivate an host.

updating netbackup server list via script-43updating netbackup server list via script-25updating netbackup server list via script-57updating netbackup server list via script-50

Hi Guys, We are currently trying to add some new media server hostnames to the the "additional servers" in Client Properties under the server tab.

The problem is that we have over 1,000 clients to change.

I know you can manually do it, which would take forever, but is there a way I could automate this via command line?

Also see: OST Configuration Standards For all Storage Server/De-duplication/OST target devices, follow the hardware installation and setup instructions before starting these steps specific to Net Backup Open Storage configurations. to replicate the data, you'll need to repeat these steps on the target system.

Also see: DDR Setup and Configuration NOTE: The "Storage Server" is the DNS name of the Data Domain's primary network interface used for backups, and does not need to be configured on the device. Depending on the device, additional authorizations or configurations may be required. Sepaton and Quantum makes no mention of this daemon, but instead has you reboot the Media Server if Solaris, or re-start Net Backup on Linux (Linux also work with just terminating nbrmms, but Solaris has other configurations that are done that require a reboot).

Refer to the following Tech Notes for details and resolutions: 6.

239, or 58; SQL DB in Loading state after restore due to typing Mistakes in the Backup or Restore Script.

Net Backup provides a pretty nice Web Interface, Ops Center, to monitor and check the basic configuration.

However after working a while with it, you may find that some information can be quit boring to find out. Symantec didn’t forget that in Unix World some peoples still like working in command lines…

These steps can also be downloaded from same location on the DXi. /bin/sh # adjust the TCP buffer size so 'setsockopt(...)' from the plugin works properly /usr/sbin/ndd -set /dev/tcp tcp_max_buf 6291456 # These are the values that we used for Solaris 10 tcp options to get maximum performance # Your environment might need different tcp options in order to obtain maximum performance # Please consult your Solaris 10 administrator manual about how to set these options for your environment /usr/sbin/ndd -set /dev/tcp tcp_xmit_hiwat 4194304 /usr/sbin/ndd -set /dev/tcp tcp_recv_hiwat 4194304 /usr/sbin/ndd -set /dev/tcp tcp_wscale_always 1 /usr/sbin/ndd -set /dev/tcp tcp_tstamp_if_wscale 1 # Quantum DXi recommendations for OST net.ipv4.tcp_rmem = 8388608 8388608 8388608 net.ipv4.tcp_wmem = 8388608 8388608 8388608 net.ipv4.tcp_mem = 10485760 10485760 10485760 netdev_max_backlog = 30000 For an example of doing the configuration via the Admin console see: Example Sepaton with OST Configuration Run this command on the Net Backup Master/Media server you want to authorize: (only needed for the first media server added - for additional media servers skip to "Add Credentials") Data Domain Recommends Running: [OST_Server] = For Data Domain this is the DNS name of the OST server's network interface you wish to send backup data to. [NBU-Server] = the Net Backup Media server name you want to authorize to use the OST Server -st 9 is for Storage type of Disk that is Network attached (1 8). System" Look for authentication messages in the file on the Data Domain system.

Hi, Its time to upgrade my netbackup clients from older ( 6.5.6 / 7.5.4/ 7.5 ) to latest 7.7.1. Is there any any bash script to update the clients will be helpful.

You must have an account to comment. Please register or login here!